Whirpool cabrio f1 error

What does f1 mean on a Whirlpool Cabrio washer?

The Cabrio Washer F1 error code happens when the main control board gets a bad signal from the water level pressure switch circuit. This is normally caused by a pinched or ripped water level pressure switch hose. Steps to take to try and remedy this error are listed below.

How do I fix a Whirlpool washer error?

If the Whirlpool washer displays the de error code on display, so there are problems with a door. Manual Review Unplug the Whirlpool washing machine from the mains. Wait for 15-20 minutes while the control unit reboots. Reset the error by pressing the START button (On/Off). Check hatch locking.

How do I reset my Whirlpool Cabrio?

Try the Cabrio Reset Procedure Or you can press PAUSE/CANCEL. Choose a cycle and press START. Then disconnect the Cabrio from power if you see the issue or error come back. Wait five minutes.

What does f1 on my dryer mean?

The ” F1 ” error means that the dryer’s thermistor failed. The dryer is reading the thermistor as “open” and the actual part has shorted out. The thermistor is used to read and control temperatures within the dryer .

How do I fix f1 error on Whirlpool oven?

F1 Error Code There may be an analog to digital failure; if this is the case, simply disconnect the range for 30 seconds and plug back in. If the same display reappears, you may need to replace the control board.

How do I fix f1 error on Whirlpool Cabrio dryer?

When the Whirlpool Cabrio displays an F1 error , this means the the control board is having difficulty communicating with the motor. To fix your F1 error , you can first try to unplug your washing machine for 15 minutes and then plug it back in. If this doesn’t work, you will need to replace the control board.

You might be interested:  Watch full f1 races

Can you reset a Whirlpool washing machine?

Press the Start Stop button once. Rotate the dial until Rinse, Wash , and Stop light illuminate. Turn the washer off and unplug it for 10 seconds. Finally, turn on the washer and it should now be reset .

Why does my washer say F 21?

The Whirlpool washer error code F21 means the washing machine has a “water draining issue”, meaning the drain pump itself, or the drain hose is clogged and the washer is having problems draining the water out.

What is e1 error in Whirlpool washing machine?

If your washing machine is not working correctly it’s safe to say it’s developed a fault. A flashing FP or F9 E1 error code on the LCD display can ring alarm bells, but it’s typically associated with a water draining problem inside the drum.

How do I run a diagnostic on my Whirlpool washer?

Whirlpool Duet Diagnostic Test Mode Close the washer door. Select any one key except “Stop/Cancel” and Control Lock. Using the same key If you got it right all the lights on the Duet washer’s control should light up, and any error codes in the washer’s memory will be displayed.

Where is the reset button on a Whirlpool Cabrio washer?

Press the Start/Stop button once. Rotate the dial until Rinse, Wash, and Stop lights illuminate. Turn the washer off and unplug it for 10 seconds. Finally, turn on the washer and it should now be reset .

How do you run a diagnostic on a Whirlpool Cabrio washer?

HOW TO ACTIVATE DIAGNOSTIC MODE ON A WHIRLPOOL CABRIO WASHER Press and hold that button for 3 seconds, then release it for 3 seconds. Press and hold it again for 3 more seconds, then release it for 3 seconds. Press and hold for 3 seconds.

You might be interested:  H1 to f1 change of status

What does error code f01 mean?

failed electronic machine control board

What does f1 code mean on Whirlpool Duet dryer?

The F01 error code means the primary control unit in the dryer has failed and will have to be replaced. The control that needs replacing is the electronic control board not the user interface and/or control panel.

What does f3 mean on a Whirlpool dryer?

not heating