Whirlpool washer e1 f1 error code

What does e1 f1 mean on Whirlpool washer?

The F1 E1 alert indicates there is an issue with the appliance control unit or associated wiring. Unplug the washer , wait two minutes, then plug back in.

How do I fix e1 error on my Whirlpool washer?

Whirlpool Washer F8 E1 Error = WATER SUPPLY ISSUE Water Supply Valves – Not Fully OPEN. Hot and cold water supplies must be turned ON. Water Inlet Hoses – Not Connected. BOTH water inlet hoses need to be connected. Drain Hose – Inserted Too Far Into Standpipe. Drain hose is inserted into the standpipe TOO FAR DOWN.

How do I clear the error code on my Whirlpool washer?

To remove the code , press pause or cancel button twice and the power button once. If the code is still displayed, unplug the washer or disconnect the power for one minute. Items were detected in the washer during the Clean Washer cycle. Remove items from the drum and restart the Clean Washer cycle.

How do you reset a Whirlpool washing machine?

How do I reset my Whirlpool washing machine ? Unplug the washer for 1 minute from the electrical outlet. Plug the washer back in and lift and lower the lid 6 times within a 12 second period. You have 30 seconds to start lifting and lowering the lid. The motor has now been reset and is ready for you to start a cycle.

What does e1 mean?

Acronym Definition
E1 Enterprise One (JD Edwards software)
E1 Echelon 1 (US DoD)
E1 European Basic Multiplex Rate (30 voice channels; 2.048 Mbps)
E1 2.048Mbps data rate (European)
You might be interested:  F1 2017 release date

How do I fix error f9 e1?

Possible Solutions If F9 E1 (drain pump system problem – long drain) appears in display, the washer is taking too long to drain water. The drain may extend more than 4.5″ (114 mm) into standpipe. Check plumbing for correct drain hose installation. Use drain hose form and attach securely to drainpipe or tub.

What does e1 and f6 mean on a Whirlpool washing machine?

Serial Communication Error

How do I run a diagnostic on my Whirlpool washer?

Whirlpool Duet Diagnostic Test Mode Close the washer door. Select any one key except “Stop/Cancel” and Control Lock. Using the same key If you got it right all the lights on the Duet washer’s control should light up, and any error codes in the washer’s memory will be displayed.

How do I reset my Whirlpool front load washer?

If they are, press START / STOP one time. Rotate your dial until you have the following three lights illuminated: RINSE, WASH, and STOP. Then turn off your washer and unplug it for ten seconds. When you turn it back on it should be reset .

What does the Code F mean on a Whirlpool washer?

door lock error

How do you fix a Whirlpool washer that won’t drain?

What to Do When Your Washing Machine Won’t Drain Perform a Master Reset. Unplug your washer for about one minute. Test the Lid Switch Assembly. See if the Drain Hose is Kinked. Check the Drain Hose or Pump for Clogs. Clean out the Coin Trap. Check the Water Level Control. Schedule Washing Machine Repair.

You might be interested:  F1 opt news

How do you troubleshoot a Whirlpool washer?

Whirlpool Washing Machine problems Washer won’t spin. Washer is making loud noise. Washer won’t agitate. Washer won’t drain. Washer vibrating or shaking. Washer fills slowly or will not fill at all. Washer leaking water. Washer won’t start.

Why does my Whirlpool washer not start?

To determine if the timer is defective, consult your washer’s wiring diagram and use a multimeter to test the timer for continuity. If the line fuse blows, the washer won’t start . To determine if the line fuse is at fault, use a multimeter to test it for continuity. If the fuse does not have continuity, replace it.