Whirlpool washer codes f1

What does f1 code on Whirlpool washer mean?

error code

Why is my Whirlpool washer flashing F?

The F /dL code indicates a door lock error on the machine. When the door fails to lock to allow the cycle to begin, it attempts to lock itself at least six times before the error appears on the digital display screen.

How do I fix e1 error on my Whirlpool washer?

Whirlpool Washer F8 E1 Error = WATER SUPPLY ISSUE Water Supply Valves – Not Fully OPEN. Hot and cold water supplies must be turned ON. Water Inlet Hoses – Not Connected. BOTH water inlet hoses need to be connected. Drain Hose – Inserted Too Far Into Standpipe. Drain hose is inserted into the standpipe TOO FAR DOWN.

How do I fix a Whirlpool washer error?

If the Whirlpool washer displays the de error code on display, so there are problems with a door. Manual Review Unplug the Whirlpool washing machine from the mains. Wait for 15-20 minutes while the control unit reboots. Reset the error by pressing the START button (On/Off). Check hatch locking.

How do you reset the code on a Whirlpool washer?

To remove the code , press pause or cancel button twice and the power button once. If the code is still displayed, unplug the washer or disconnect the power for one minute. Items were detected in the washer during the Clean Washer cycle. Remove items from the drum and restart the Clean Washer cycle.

How do I know if my washing machine control board is bad?

A failed front-load washing machine control board has several symptoms, including the washer not starting, filling, spinning or draining.

You might be interested:  Social security number for f1 students

Can you reset a Whirlpool washing machine?

Press the Start Stop button once. Rotate the dial until Rinse, Wash , and Stop light illuminate. Turn the washer off and unplug it for 10 seconds. Finally, turn on the washer and it should now be reset .

How do I unlock my whirlpool?

Whirlpool Oven Door is Locked – What Should I Do? Press Cancel/Off key to start a latch reset, wait 20-30 seconds and open door. Turn the power off at the circuit breaker or fuse box for one minute, then turn the power back on.

What is e1 error in washing machine?

When the Washing Machine is displaying E1 in the panel, it is indicating an error in the water supply. The appliance is not detecting that the unit is filling with water.

How do I fix e1 error on my washing machine?

If the error code E1 appears, there is a problem draining the water. First, check the washing machine’s filter.

What does e1 mean?

Acronym Definition
E1 Enterprise One (JD Edwards software)
E1 Echelon 1 (US DoD)
E1 European Basic Multiplex Rate (30 voice channels; 2.048 Mbps)
E1 2.048Mbps data rate (European)

Why does my washer say F 21?

The Whirlpool washer error code F21 means the washing machine has a “water draining issue”, meaning the drain pump itself, or the drain hose is clogged and the washer is having problems draining the water out.

How do I reset my washing machine?

Top Load Washer – Hydrowave Motor Reset Unplug the washer for 1 minute from the electrical outlet. Plug the washer back in and lift and lower the lid 6 times within a 12 second period. You have 30 seconds to start lifting and lowering the lid. The motor has now been reset and is ready for you to start a cycle.

You might be interested:  F1 opt visa rules

Why does my Whirlpool washer says low detergent?

Detergent Level Low – This will light (yellow) if there is enough detergent in the Load & Go™ cartridge for only a few more cycles. Empty – This will light (red) if there is no detergent in the Load & Go™ cartridge.