Whirlpool dryer f1 error code

How do I fix f01 on my Whirlpool dryer?

The Whirlpool Duet Dryer F01 error may be able to be fixed with a simple reset of the main control. Unplug the dryer for 1 minute and plug it back in this will reset the control if the error persists after that you will need to check the dryer thermal fuse.

How do I reset my Whirlpool front load dryer?

If your Whirlpool dryer displays a “PF” error code, indicating a recent power failure, the dryer will need to be reset and restarted. This is done by pressing “Start” for a few seconds to restart the dryer . If the dryer does not restart automatically, select a new cycle and any options then press “Start” to begin.

How do I reset my Whirlpool Cabrio dryer?

How to Reset a Whirlpool Cabrio Touch any key on the display pad to clear the error code, if applicable, or press “Pause/Cancel.” Choose a new cycle and press “Start” to begin. Turn off and disconnect the Cabrio if the error or problem persists. Wait several minutes before restoring power. Contact Whirlpool for assistance if the unit will not reset .

What does error code f01 mean?

failed electronic machine control board

What does f1 on my dryer mean?

The ” F1 ” error means that the dryer’s thermistor failed. The dryer is reading the thermistor as “open” and the actual part has shorted out. The thermistor is used to read and control temperatures within the dryer .

Where is the dryer reset button?

Often, dryers are equipped with a reset button on the control panel. If the motor won’t run, let the dryer cool for about ten minutes. Then press this reset button .

You might be interested:  F1 race tracks

Why is my Whirlpool dryer not coming on?

The thermal fuse is the most common problem with Whirlpool dryers not running. The thermal fuse cuts the dryer off in the event it overheats. So if your thermal fuse is bad you should check the vent. To check the thermal fuse, first unplug dryer and remove back.

How do you run a diagnostic on a Whirlpool Duet dryer?

press and hold for three seconds, release for three seconds; press and hold for three seconds. You’ll know you’ve entered diagnostic mode because all the indicators on the console will light up for five seconds and you’ll see the code “88” in the Estimated Time Remaining display.

What do you do when your dryer won’t start?

Unplug the dryer and check the thermal fuse for continuity. Replace the thermal fuse if the multimeter measures no continuity. Check the exhaust vent because a clog in the vent likely caused the thermal fuse to blow. For dryers with a dial timer, a broken push-to- start switch can prevent the motor from running.

How do you troubleshoot a Whirlpool Cabrio dryer?

Troubleshooting your Whirlpool Cabrio will take about 15 minutes. Verify that the dryer is still plugged into its outlet. Ensure that your household fuses or breakers are active. Push the dryer door to make sure it is tightly closed. Press and hold the “Start/Pause” button for up to five seconds.

What does error code f01 mean on Whirlpool Duet dryer?

The F01 error code means the primary control unit in the dryer has failed and will have to be replaced. The control that needs replacing is the electronic control board not the user interface and/or control panel.

You might be interested:  Mclaren f1 rear

How do I clear the error code on my Whirlpool washer?

To remove the code , press pause or cancel button twice and the power button once. If the code is still displayed, unplug the washer or disconnect the power for one minute. Items were detected in the washer during the Clean Washer cycle. Remove items from the drum and restart the Clean Washer cycle.

How do you test a dryer control board?

How to test your dryer’s rotary switch: Unplug your dryer and remove the control console panel on the top of your dryer to locate the rotary switch. Set your multi-meter to the Rx1 setting and place the probes on the switch’s terminals. With the probes still touching the terminals, press in on and hold the switch.