Whirlpool cabrio washer f1 error repair

What does f1 mean on my Whirlpool Cabrio washer?

The Cabrio Washer F1 error code happens when the main control board gets a bad signal from the water level pressure switch circuit. This is normally caused by a pinched or ripped water level pressure switch hose.

How do I reset my Whirlpool Cabrio washer?

Press the Start/Stop button once. Rotate the dial until Rinse, Wash , and Stop lights illuminate. Turn the washer off and unplug it for 10 seconds. Finally, turn on the washer and it should now be reset .

How do I fix a Whirlpool washer error?

If the Whirlpool washer displays the de error code on display, so there are problems with a door. Manual Review Unplug the Whirlpool washing machine from the mains. Wait for 15-20 minutes while the control unit reboots. Reset the error by pressing the START button (On/Off). Check hatch locking.

How do I fix the error code on a Whirlpool Cabrio washer?

Whirlpool Cabrio Washer Error LD Make sure the pump and drain hose are clear of debris that would cause a blockage. Check the impeller on the drain pump and make sure its not wobbly or busted. Remove the tub hose from the pump to the tub and check it for blockage. Make sure the pump is running when and getting the proper voltage when it should be.

How do I know if my washing machine control board is bad?

A failed front-load washing machine control board has several symptoms, including the washer not starting, filling, spinning or draining.

How do I fix f1 error in AC?

The error code ‘ F1 ‘ means the indoor unit PCB and outdoor unit PCB cannot communicate with each other. To fix the problem you can do the following: Check all connections are clean and tight. Corrosion on connections can cause this error , use light abrasive paper to clean each one.

You might be interested:  F1 nbc tv schedule

How do I run a diagnostic on my Whirlpool washer?

Whirlpool Duet Diagnostic Test Mode Close the washer door. Select any one key except “Stop/Cancel” and Control Lock. Using the same key If you got it right all the lights on the Duet washer’s control should light up, and any error codes in the washer’s memory will be displayed.

How do you run a diagnostic on a Whirlpool Cabrio washer?

HOW TO ACTIVATE DIAGNOSTIC MODE ON A WHIRLPOOL CABRIO WASHER Press and hold that button for 3 seconds, then release it for 3 seconds. Press and hold it again for 3 more seconds, then release it for 3 seconds. Press and hold for 3 seconds.

Why won’t my Cabrio washer fill with water?

If you find your Whirlpool Cabrio washer not filling with water , the inlet hoses and screens may be at fault. Metal screens attached to both ends of the inlet hoses protect the water inlet valve from sediment and debris. To inspect the screens for signs of clogging, turn off the main water supply.

How do I reset my Whirlpool top load washer?

How do I reset my Whirlpool washing machine ? Unplug the washer for 1 minute from the electrical outlet. Plug the washer back in and lift and lower the lid 6 times within a 12 second period. You have 30 seconds to start lifting and lowering the lid. The motor has now been reset and is ready for you to start a cycle.

How do I fix e1 error on my Whirlpool washer?

Whirlpool Washer F8 E1 Error = WATER SUPPLY ISSUE Water Supply Valves – Not Fully OPEN. Hot and cold water supplies must be turned ON. Water Inlet Hoses – Not Connected. BOTH water inlet hoses need to be connected. Drain Hose – Inserted Too Far Into Standpipe. Drain hose is inserted into the standpipe TOO FAR DOWN.

You might be interested:  China f1 result

How do I reset my washing machine?

Top Load Washer – Hydrowave Motor Reset Unplug the washer for 1 minute from the electrical outlet. Plug the washer back in and lift and lower the lid 6 times within a 12 second period. You have 30 seconds to start lifting and lowering the lid. The motor has now been reset and is ready for you to start a cycle.

Why is my washing machine not draining all the way?

Your washer may have a clogged drain hose or the pump may be broken. A broken lid switch or belt could also be the culprit. It may even be something as simple as the the hose being jammed. The washer pump forces water from the bottom of the machine into the drain hose.

What does it mean when your washing machine says LD?

drain pump system problem – long drain