Whirlpool cabrio washer codes f1

What does f1 code mean on Whirlpool Cabrio washer?

The Cabrio Washer F1 error code happens when the main control board gets a bad signal from the water level pressure switch circuit. If the issue continues and F1 flashes repeatedly when pressing the power button then the main control needs to be replaced.

What does it mean when a washer says f1?

error code

How do you clear the codes on a Whirlpool Cabrio washer?

If your washer is still not working correctly, you can try the Cabrio reset procedure. Touch any button that you see on your display pad. This will clear the error code . Or you can press PAUSE/CANCEL.

Can you reset a Whirlpool Cabrio washing machine?

If you need to reset a Whirlpool Cabrio washing machine , you can try the following: Rotate the dial until Rinse, Wash , and Stop lights illuminate. Turn the washer off and unplug it for 10 seconds. Finally, turn on the washer and it should now be reset .

How do I fix f1 error on Whirlpool oven?

F1 Error Code There may be an analog to digital failure; if this is the case, simply disconnect the range for 30 seconds and plug back in. If the same display reappears, you may need to replace the control board.

How do I fix f1 error on Whirlpool Cabrio dryer?

When the Whirlpool Cabrio displays an F1 error , this means the the control board is having difficulty communicating with the motor. To fix your F1 error , you can first try to unplug your washing machine for 15 minutes and then plug it back in. If this doesn’t work, you will need to replace the control board.

You might be interested:  F1 visa minimum credit hours requirement

How do I know if my washing machine control board is bad?

A failed front-load washing machine control board has several symptoms, including the washer not starting, filling, spinning or draining.

How do I fix f1 error in AC?

The error code ‘ F1 ‘ means the indoor unit PCB and outdoor unit PCB cannot communicate with each other. To fix the problem you can do the following: Check all connections are clean and tight. Corrosion on connections can cause this error , use light abrasive paper to clean each one.

How do I fix f01 error?

The F01 indicates a failed electronic machine control board. This error code can sometimes be caused by a glitch or power surge through the electrical lines. You may be able to clear this code by unplugging the washer for 5 minutes.

How do I reset my Whirlpool Cabrio Top load washer?

Press the Start Stop button once. Rotate the dial until Rinse, Wash, and Stop light illuminate. Turn the washer off and unplug it for 10 seconds. Finally, turn on the washer and it should now be reset .

Why does my washer say F?

The F /dL code indicates a door lock error on the machine. When the door fails to lock to allow the cycle to begin, it attempts to lock itself at least six times before the error appears on the digital display screen. When the door fails to lock, the machine won’t run at all.

How do I reset my Whirlpool top load washer?

How do I reset my Whirlpool washing machine ? Unplug the washer for 1 minute from the electrical outlet. Plug the washer back in and lift and lower the lid 6 times within a 12 second period. You have 30 seconds to start lifting and lowering the lid. The motor has now been reset and is ready for you to start a cycle.

You might be interested:  F1 italian grand prix

Why won’t my Cabrio washer fill with water?

If you find your Whirlpool Cabrio washer not filling with water , the inlet hoses and screens may be at fault. Metal screens attached to both ends of the inlet hoses protect the water inlet valve from sediment and debris. To inspect the screens for signs of clogging, turn off the main water supply.

How do I run a diagnostic on my Whirlpool washer?

Whirlpool Duet Diagnostic Test Mode Close the washer door. Select any one key except “Stop/Cancel” and Control Lock. Using the same key If you got it right all the lights on the Duet washer’s control should light up, and any error codes in the washer’s memory will be displayed.

How do you run a diagnostic on a Whirlpool Cabrio washer?

HOW TO ACTIVATE DIAGNOSTIC MODE ON A WHIRLPOOL CABRIO WASHER Press and hold that button for 3 seconds, then release it for 3 seconds. Press and hold it again for 3 more seconds, then release it for 3 seconds. Press and hold for 3 seconds.