Whirlpool cabrio f1 error code recall

What does f1 code mean on Whirlpool Cabrio washer?

The Cabrio Washer F1 error code happens when the main control board gets a bad signal from the water level pressure switch circuit. If the issue continues and F1 flashes repeatedly when pressing the power button then the main control needs to be replaced.

What does it mean when a washer says f1?

error code

How do I reset my Whirlpool Cabrio dryer?

How to Reset a Whirlpool Cabrio Touch any key on the display pad to clear the error code, if applicable, or press “Pause/Cancel.” Choose a new cycle and press “Start” to begin. Turn off and disconnect the Cabrio if the error or problem persists. Wait several minutes before restoring power. Contact Whirlpool for assistance if the unit will not reset .

How do I fix a Whirlpool washer error?

If the Whirlpool washer displays the de error code on display, so there are problems with a door. Manual Review Unplug the Whirlpool washing machine from the mains. Wait for 15-20 minutes while the control unit reboots. Reset the error by pressing the START button (On/Off). Check hatch locking.

How do I fix f1 error on Whirlpool oven?

F1 Error Code There may be an analog to digital failure; if this is the case, simply disconnect the range for 30 seconds and plug back in. If the same display reappears, you may need to replace the control board.

How do I fix f1 error on Whirlpool Cabrio dryer?

When the Whirlpool Cabrio displays an F1 error , this means the the control board is having difficulty communicating with the motor. To fix your F1 error , you can first try to unplug your washing machine for 15 minutes and then plug it back in. If this doesn’t work, you will need to replace the control board.

You might be interested:  F1 driver who died in 1975

How do I fix f1 error in AC?

The error code ‘ F1 ‘ means the indoor unit PCB and outdoor unit PCB cannot communicate with each other. To fix the problem you can do the following: Check all connections are clean and tight. Corrosion on connections can cause this error , use light abrasive paper to clean each one.

How do I know if my washing machine control board is bad?

A failed front-load washing machine control board has several symptoms, including the washer not starting, filling, spinning or draining.

How do I reset my Whirlpool Cabrio touchscreen?

This is the first step you are done to reset the Whirlpool Cabrio washing machine . Press PAUSE/CANCEL twice to cancel the cycle. The washer will drain. Press POWER. Select the desired wash cycle. Select the desired Modifiers and Options. Press START.

How do you troubleshoot a Whirlpool Cabrio dryer?

Troubleshooting your Whirlpool Cabrio will take about 15 minutes. Verify that the dryer is still plugged into its outlet. Ensure that your household fuses or breakers are active. Push the dryer door to make sure it is tightly closed. Press and hold the “Start/Pause” button for up to five seconds.

Where is the dryer reset button?

Often, dryers are equipped with a reset button on the control panel. If the motor won’t run, let the dryer cool for about ten minutes. Then press this reset button .

How do I reset my thermal fuse?

How do you change a thermal fuse on a dryer ? Shut off the power. Unplug the dryer to disconnect electrical power. Remove the back panel. Remove the fuse . Install the new thermal fuse . Reattach the back panel. Plug in the dryer . Clean the exhaust vent.

You might be interested:  Netflix f1 documentary

How do I fix e1 error on my Whirlpool washer?

Whirlpool Washer F8 E1 Error = WATER SUPPLY ISSUE Water Supply Valves – Not Fully OPEN. Hot and cold water supplies must be turned ON. Water Inlet Hoses – Not Connected. BOTH water inlet hoses need to be connected. Drain Hose – Inserted Too Far Into Standpipe. Drain hose is inserted into the standpipe TOO FAR DOWN.

How do I reset my Whirlpool washing machine?

How do I reset my Whirlpool washing machine ? Unplug the washer for 1 minute from the electrical outlet. Plug the washer back in and lift and lower the lid 6 times within a 12 second period. You have 30 seconds to start lifting and lowering the lid. The motor has now been reset and is ready for you to start a cycle.

How do you reset a Whirlpool front load washer?

If they are, press START / STOP one time. Rotate your dial until you have the following three lights illuminated: RINSE, WASH, and STOP. Then turn off your washer and unplug it for ten seconds. When you turn it back on it should be reset .