Whirlpool cabrio f1 codes

What does f1 code mean on Whirlpool Cabrio washer?

The Cabrio Washer F1 error code happens when the main control board gets a bad signal from the water level pressure switch circuit. If the issue continues and F1 flashes repeatedly when pressing the power button then the main control needs to be replaced.

What does it mean when a washer says f1?

error code

How do I reset my Whirlpool Cabrio dryer?

How to Reset a Whirlpool Cabrio Touch any key on the display pad to clear the error code, if applicable, or press “Pause/Cancel.” Choose a new cycle and press “Start” to begin. Turn off and disconnect the Cabrio if the error or problem persists. Wait several minutes before restoring power. Contact Whirlpool for assistance if the unit will not reset .

How do I fix f1 error on Whirlpool Cabrio dryer?

When the Whirlpool Cabrio displays an F1 error , this means the the control board is having difficulty communicating with the motor. To fix your F1 error , you can first try to unplug your washing machine for 15 minutes and then plug it back in. If this doesn’t work, you will need to replace the control board.

How do I fix f1 error on Whirlpool oven?

F1 Error Code There may be an analog to digital failure; if this is the case, simply disconnect the range for 30 seconds and plug back in. If the same display reappears, you may need to replace the control board.

How do I fix f1 error in AC?

The error code ‘ F1 ‘ means the indoor unit PCB and outdoor unit PCB cannot communicate with each other. To fix the problem you can do the following: Check all connections are clean and tight. Corrosion on connections can cause this error , use light abrasive paper to clean each one.

You might be interested:  F1 australia 2016

How do I know if my washing machine control board is bad?

A failed front-load washing machine control board has several symptoms, including the washer not starting, filling, spinning or draining.

How do I clear the error code on my Whirlpool washer?

To remove the code , press pause or cancel button twice and the power button once. If the code is still displayed, unplug the washer or disconnect the power for one minute. Items were detected in the washer during the Clean Washer cycle. Remove items from the drum and restart the Clean Washer cycle.

How do you troubleshoot a Whirlpool Cabrio dryer?

Troubleshooting your Whirlpool Cabrio will take about 15 minutes. Verify that the dryer is still plugged into its outlet. Ensure that your household fuses or breakers are active. Push the dryer door to make sure it is tightly closed. Press and hold the “Start/Pause” button for up to five seconds.

How do I reset my Whirlpool Cabrio Platinum?

Press the Start/Stop button once. Rotate the dial until Rinse, Wash, and Stop lights illuminate. Turn the washer off and unplug it for 10 seconds. Finally, turn on the washer and it should now be reset .

How do I reset my Whirlpool Cabrio touchscreen?

This is the first step you are done to reset the Whirlpool Cabrio washing machine . Press PAUSE/CANCEL twice to cancel the cycle. The washer will drain. Press POWER. Select the desired wash cycle. Select the desired Modifiers and Options. Press START.

How do I run a diagnostic on a Whirlpool Cabrio?

HOW TO ACTIVATE DIAGNOSTIC MODE ON A WHIRLPOOL CABRIO WASHER Press and hold that button for 3 seconds, then release it for 3 seconds. Press and hold it again for 3 more seconds, then release it for 3 seconds. Press and hold for 3 seconds.

You might be interested:  Mclaren f1 gtr price

How do I run a diagnostic on my Whirlpool washer?

Now you can do an automatic diagnostic washer cycle. You will need to start the diagnostics mode again, but this time turn the washer cycle knob right until only the “spin” light is lit and press “start”. The washer will do a quick cycle that will test all the washer functions.