Whirlpool cabrio f1 code

What does f1 code mean on Whirlpool Cabrio washer?

The Cabrio Washer F1 error code happens when the main control board gets a bad signal from the water level pressure switch circuit. If the issue continues and F1 flashes repeatedly when pressing the power button then the main control needs to be replaced.

What does it mean when a washer says f1?

error code

How do you reset the codes on a Whirlpool Cabrio washer?

How to Reset a Whirlpool Cabrio Touch any key on the display pad to clear the error code , if applicable, or press “Pause/Cancel.” Choose a new cycle and press “Start” to begin. Turn off and disconnect the Cabrio if the error or problem persists. Wait several minutes before restoring power.

How do I fix f1 error on Whirlpool Cabrio dryer?

When the Whirlpool Cabrio displays an F1 error , this means the the control board is having difficulty communicating with the motor. To fix your F1 error , you can first try to unplug your washing machine for 15 minutes and then plug it back in. If this doesn’t work, you will need to replace the control board.

How do I fix f1 error on Whirlpool oven?

F1 Error Code There may be an analog to digital failure; if this is the case, simply disconnect the range for 30 seconds and plug back in. If the same display reappears, you may need to replace the control board.

How do I fix f1 error in AC?

The error code ‘ F1 ‘ means the indoor unit PCB and outdoor unit PCB cannot communicate with each other. To fix the problem you can do the following: Check all connections are clean and tight. Corrosion on connections can cause this error , use light abrasive paper to clean each one.

You might be interested:  F1 2019 team standings

How do I know if my washing machine control board is bad?

A failed front-load washing machine control board has several symptoms, including the washer not starting, filling, spinning or draining.

How do I fix f01 error?

The F01 indicates a failed electronic machine control board. This error code can sometimes be caused by a glitch or power surge through the electrical lines. You may be able to clear this code by unplugging the washer for 5 minutes.

How do I run a diagnostic on my Whirlpool washer?

Whirlpool Duet Diagnostic Test Mode Close the washer door. Select any one key except “Stop/Cancel” and Control Lock. Using the same key If you got it right all the lights on the Duet washer’s control should light up, and any error codes in the washer’s memory will be displayed.

Why won’t my Cabrio washer fill with water?

If you find your Whirlpool Cabrio washer not filling with water , the inlet hoses and screens may be at fault. Metal screens attached to both ends of the inlet hoses protect the water inlet valve from sediment and debris. To inspect the screens for signs of clogging, turn off the main water supply.

How do I reset my Whirlpool top load washer?

How do I reset my Whirlpool washing machine ? Unplug the washer for 1 minute from the electrical outlet. Plug the washer back in and lift and lower the lid 6 times within a 12 second period. You have 30 seconds to start lifting and lowering the lid. The motor has now been reset and is ready for you to start a cycle.

You might be interested:  F1 2016 mobile game

How do you calibrate a Whirlpool Cabrio?

CABRIO WASHER CALIBRATION CYCLE Pick three buttons ( Do not use Power button) and within 8 seconds. Make sure the washer is in (Stand By Mode) which means the machine is plugged in and all the indicator lights are off. Press and Release the 1st selected button, Press and Release the 2nd selected button,

How do you troubleshoot a Whirlpool Cabrio washer?

Troubleshooting Whirlpool Cabrio Washer Problems Washer Making Unusual Noises. Washer Won’t Start. Lid Lock Issues . Deciphering the LD Error Code. Washer Leaves Deposits on Dark Clothes. Washer Has a Burned Plastic Odor. Rust Spots on Washer Lid.