Whirlpool cabrio error codes f1

What does f1 code mean on Whirlpool Cabrio washer?

The Cabrio Washer F1 error code happens when the main control board gets a bad signal from the water level pressure switch circuit. If the issue continues and F1 flashes repeatedly when pressing the power button then the main control needs to be replaced.

What does it mean when a washer says f1?

error code

How do I fix a Whirlpool washer error?

If the Whirlpool washer displays the de error code on display, so there are problems with a door. Manual Review Unplug the Whirlpool washing machine from the mains. Wait for 15-20 minutes while the control unit reboots. Reset the error by pressing the START button (On/Off). Check hatch locking.

How do I reset my Whirlpool Cabrio touchscreen?

Procedure Detail It’s time to press the on and off button just one time. Now check the machine by rotating the dial until rinse, wash, and stoplight. Now turn the washer off and unplug it for a few seconds. This is the procedure to reset the machine if it’s not properly reset repeat the process one more time.

How do I fix f1 error on Whirlpool oven?

F1 Error Code There may be an analog to digital failure; if this is the case, simply disconnect the range for 30 seconds and plug back in. If the same display reappears, you may need to replace the control board.

How do I fix f1 error on Whirlpool Cabrio dryer?

When the Whirlpool Cabrio displays an F1 error , this means the the control board is having difficulty communicating with the motor. To fix your F1 error , you can first try to unplug your washing machine for 15 minutes and then plug it back in. If this doesn’t work, you will need to replace the control board.

You might be interested:  F1 resident alien or nonresident alien

How do I fix f1 error in AC?

The error code ‘ F1 ‘ means the indoor unit PCB and outdoor unit PCB cannot communicate with each other. To fix the problem you can do the following: Check all connections are clean and tight. Corrosion on connections can cause this error , use light abrasive paper to clean each one.

How do I know if my washing machine control board is bad?

A failed front-load washing machine control board has several symptoms, including the washer not starting, filling, spinning or draining.

How do I fix f01 error?

The F01 indicates a failed electronic machine control board. This error code can sometimes be caused by a glitch or power surge through the electrical lines. You may be able to clear this code by unplugging the washer for 5 minutes.

How do I fix e1 error on my Whirlpool washer?

Whirlpool Washer F8 E1 Error = WATER SUPPLY ISSUE Water Supply Valves – Not Fully OPEN. Hot and cold water supplies must be turned ON. Water Inlet Hoses – Not Connected. BOTH water inlet hoses need to be connected. Drain Hose – Inserted Too Far Into Standpipe. Drain hose is inserted into the standpipe TOO FAR DOWN.

Can you reset a Whirlpool washing machine?

Press the Start Stop button once. Rotate the dial until Rinse, Wash , and Stop light illuminate. Turn the washer off and unplug it for 10 seconds. Finally, turn on the washer and it should now be reset .

How do I reset my washing machine?

Top Load Washer – Hydrowave Motor Reset Unplug the washer for 1 minute from the electrical outlet. Plug the washer back in and lift and lower the lid 6 times within a 12 second period. You have 30 seconds to start lifting and lowering the lid. The motor has now been reset and is ready for you to start a cycle.

You might be interested:  F1 visa fee

How do I run a diagnostic on a Whirlpool Cabrio?

HOW TO ACTIVATE DIAGNOSTIC MODE ON A WHIRLPOOL CABRIO WASHER Press and hold that button for 3 seconds, then release it for 3 seconds. Press and hold it again for 3 more seconds, then release it for 3 seconds. Press and hold for 3 seconds.

Why does my Whirlpool washer not start?

To determine if the timer is defective, consult your washer’s wiring diagram and use a multimeter to test the timer for continuity. If the line fuse blows, the washer won’t start . To determine if the line fuse is at fault, use a multimeter to test it for continuity. If the fuse does not have continuity, replace it.

How do I clear the SD card code on a Whirlpool Cabrio?

The washer will try to fix this itself by extending the rinse time to clear the suds, if it is able to clear them and no more drag is detected on the tub the Cabrio Washer Error SD code will clear from the display. If the error persists then the steps to take to try and remedy this error are listed below.