Whirlpool cabrio error code f1

What does f1 mean on my Whirlpool Cabrio washer?

The Cabrio Washer F1 error code happens when the main control board gets a bad signal from the water level pressure switch circuit. This is normally caused by a pinched or ripped water level pressure switch hose.

What does it mean when a washer says f1?

error code

How do I reset my Whirlpool Cabrio?

Try the Cabrio Reset Procedure Or you can press PAUSE/CANCEL. Choose a cycle and press START. Then disconnect the Cabrio from power if you see the issue or error come back. Wait five minutes.

How do I fix SD error on Whirlpool Cabrio?

If your washer displays an SD error and will not go into the spin cycle, then the basket drive hub might need replacing. The whole tub should spin along with the impeller. If you can rotate the impeller while holding the inside tub still with your hand, then this might indicate that your drive hub needs replacing.

How do I fix f1 error on Whirlpool oven?

F1 Error Code There may be an analog to digital failure; if this is the case, simply disconnect the range for 30 seconds and plug back in. If the same display reappears, you may need to replace the control board.

How do I fix f1 error on Whirlpool Cabrio dryer?

When the Whirlpool Cabrio displays an F1 error , this means the the control board is having difficulty communicating with the motor. To fix your F1 error , you can first try to unplug your washing machine for 15 minutes and then plug it back in. If this doesn’t work, you will need to replace the control board.

You might be interested:  F1 work visa

How do I fix f1 error in AC?

The error code ‘ F1 ‘ means the indoor unit PCB and outdoor unit PCB cannot communicate with each other. To fix the problem you can do the following: Check all connections are clean and tight. Corrosion on connections can cause this error , use light abrasive paper to clean each one.

How do I clear the error code on my Whirlpool washer?

To remove the code , press pause or cancel button twice and the power button once. If the code is still displayed, unplug the washer or disconnect the power for one minute. Items were detected in the washer during the Clean Washer cycle. Remove items from the drum and restart the Clean Washer cycle.

How do I know if my washing machine control board is bad?

A failed front-load washing machine control board has several symptoms, including the washer not starting, filling, spinning or draining.

How do I run a diagnostic on my Whirlpool washer?

Whirlpool Duet Diagnostic Test Mode Close the washer door. Select any one key except “Stop/Cancel” and Control Lock. Using the same key If you got it right all the lights on the Duet washer’s control should light up, and any error codes in the washer’s memory will be displayed.

Where is the reset button on a Whirlpool Cabrio washer?

Press the Start/Stop button once. Rotate the dial until Rinse, Wash, and Stop lights illuminate. Turn the washer off and unplug it for 10 seconds. Finally, turn on the washer and it should now be reset .

You might be interested:  Can f1 students work

How do you troubleshoot a Whirlpool Cabrio washer?

Troubleshooting Whirlpool Cabrio Washer Problems Washer Making Unusual Noises. Washer Won’t Start. Lid Lock Issues . Deciphering the LD Error Code. Washer Leaves Deposits on Dark Clothes. Washer Has a Burned Plastic Odor. Rust Spots on Washer Lid.

What does SD mean on Whirlpool Cabrio?

excessive detergent suds

What is f71 error code?

Bonnie Frerking ,”the F70 and F71 error codes on this model of washer indicates a communication problem between the user interface control board and the central control unit (main control board). These error codes can sometimes be caused by a power surge or glitch through the electrical lines.

How do I fix my Maytag SD error?

Maytag acknowledges that error codes like ” Sd ” sometimes appear by mistake. Push the “Pause/Cancel” twice or “Power” button once to remove the code from the screen and try using the washer again. If the code returns, unplug the washer for 60 seconds and try the cycle again before calling for assistance.