Whirlpool cabrio dryer f1 error

What does f1 mean on my dryer?

Definition . The ” F1 ” error means that the dryer’s thermistor failed. The dryer is reading the thermistor as “open” and the actual part has shorted out. The thermistor is used to read and control temperatures within the dryer . Without the part, the dryer will not operate.

What is f1 error on Whirlpool Cabrio?

The Cabrio Washer F1 error code happens when the main control board gets a bad signal from the water level pressure switch circuit. This is normally caused by a pinched or ripped water level pressure switch hose.

How do you reset a Whirlpool Cabrio dryer?

How to Reset a Whirlpool Cabrio Touch any key on the display pad to clear the error code, if applicable, or press “Pause/Cancel.” Choose a new cycle and press “Start” to begin. Turn off and disconnect the Cabrio if the error or problem persists. Wait several minutes before restoring power. Contact Whirlpool for assistance if the unit will not reset .

Where is the fuse on a Whirlpool Cabrio dryer?

Push “Power” to turn on the dryer . If the dryer turns on but does not provide heat, unplug the dryer’s power cord and locate your home’s fuse box. The fuse box is typically located in the basement or utility area.

How do I fix f01 on my Whirlpool dryer?

The Whirlpool Duet Dryer F01 error may be able to be fixed with a simple reset of the main control. Unplug the dryer for 1 minute and plug it back in this will reset the control if the error persists after that you will need to check the dryer thermal fuse.

You might be interested:  General admission f1 austin

What does e1 mean on a Whirlpool dryer?

The Whirlpool Duet Dryer Error E1 means the control has detected that the thermistor is open. This error can be a wiring issue from the control to the thermistor or a bad thermistor.

How do I fix f1 error in AC?

The error code ‘ F1 ‘ means the indoor unit PCB and outdoor unit PCB cannot communicate with each other. To fix the problem you can do the following: Check all connections are clean and tight. Corrosion on connections can cause this error , use light abrasive paper to clean each one.

How do I fix f01 error?

The F01 indicates a failed electronic machine control board. This error code can sometimes be caused by a glitch or power surge through the electrical lines. You may be able to clear this code by unplugging the washer for 5 minutes.

How do I reset my Whirlpool Cabrio touchscreen?

This is the first step you are done to reset the Whirlpool Cabrio washing machine . Press PAUSE/CANCEL twice to cancel the cycle. The washer will drain. Press POWER. Select the desired wash cycle. Select the desired Modifiers and Options. Press START.

How do you troubleshoot a Whirlpool Cabrio dryer?

Troubleshooting your Whirlpool Cabrio will take about 15 minutes. Verify that the dryer is still plugged into its outlet. Ensure that your household fuses or breakers are active. Push the dryer door to make sure it is tightly closed. Press and hold the “Start/Pause” button for up to five seconds.

Is there a reset button on my Whirlpool dryer?

If your Whirlpool dryer displays a “PF” error code, indicating a recent power failure, the dryer will need to be reset and restarted. This is done by pressing “Start” for a few seconds to restart the dryer . If the dryer does not restart automatically, select a new cycle and any options then press “Start” to begin.

You might be interested:  F1 2016 standings

How do I know if my thermal fuse is blown?

To test if your thermal fuse has blown , touch the right side of your multimeter lead to the right side of the fuse , and repeat with the left multimeter lead. If the multimeter needle fails to move, this indicates the thermal fuse has blown . Learn about testing for a blown fuse .

Where is the reset button on a dryer?

There is no reset button on your dryer . I recommend locating the two (2) house circuit breakers dedicated for the dryer and reset both circuit breakers by flipping them both OFF and ON 2-3 times and then check to see if the dryer will start.

How do I reset my thermal fuse?

How do you change a thermal fuse on a dryer ? Shut off the power. Unplug the dryer to disconnect electrical power. Remove the back panel. Remove the fuse . Install the new thermal fuse . Reattach the back panel. Plug in the dryer . Clean the exhaust vent.