Maytag oven f1 code

What does it mean when my oven says f1?

The F1 error means that there is an electronics failure within the oven . This failure can occur within the keypad itself, the electronic oven control or the oven temperature sensor.

How do I reset my Maytag oven?

Simply turn off the oven , unplug it for five minutes, and then plug it back in and restart . Also, make sure the fuse wasn’t tripped at the circuit breaker and that the outlet provides the correct voltage for the oven .

How do you unlock a Maytag oven?

Door is locked when starting or using the oven Turn the power off at the circuit breaker or fuse box for one minute, then turn the power back on. Allow the oven to cool, approximately 30-90 minutes, move the latch arm to the left to unlock the door.

What does it mean when my oven says f3?

The F3 error code indicates a problem with the oven temperature sensor, the electronic oven control (EOC), or the wiring in between. To test the range someone needs to access the rear of the EOC.

How do I fix f1 error on Whirlpool oven?

F1 Error Code There may be an analog to digital failure; if this is the case, simply disconnect the range for 30 seconds and plug back in. If the same display reappears, you may need to replace the control board.

How do you fix an f1 oven?

Oven Temperature Probe Press the “Probe” button on the keypad and use the keys to enter the desired cooking temperature. Push “Start” to reset the probe and begin cooking. If the F1 error code does not return, the problem is resolved and cooking should proceed normally.

You might be interested:  Watch f1 races replay

Do stoves have a reset button?

Some older ovens have their own set of fuses located under the range top, in the back of the oven space, or behind the oven. Your oven might also have a circuit breaker with a reset button on the control console or on top of the oven that needs to be reset . If you are still confounded, pull the oven away from the wall.

How do I reset my Maytag Gemini oven?

Reset power to the product: Power unit down by turning off the circuit breaker(s) for one (1) minute. Power unit up by turning on the circuit breaker(s). Monitor the oven /range for one (1) minute to ensure the error code does not display again. Verify oven operation.

Why does my stove keep beeping f1?

The ” F1 ” fault code generally implies an electronic oven control (EOC) failure. Disconnect the power, wait 30 seconds or longer and then reapply power. If ” F1 ” returns upon power-up, replace the electronic oven control. The oven control can be accessed and replaced from the rear of the control panel.

How do you unlock the hinges on an oven door?

If your oven door does not have hinge latches to unlock , simply open to the broil stop position and carefully pull the door up and away from the oven . Carefully remove the door by grabbing each side firmly and lifting up until it pops off of and away from the oven .

How do you unlock a self cleaning oven door?

Unlocking the Oven After Self – Cleaning . Unplug the oven for 5 minutes, plug it back in, and press “Clear/Off”. This can sometimes prompt the oven’s computer to reset and release the lock button.

You might be interested:  Used f1 cars for sale

What does oven lock mean?

LOC means the control panel is locked . Per the Use and Care Guide: 1. Check that the oven and cooktop are off.

What does e2 f3 mean on a Whirlpool oven?

Manage My Life August 11th, 2008. Best answer. The error code F3 E2 is telling you the electronic control on the range detected a high temperature in the oven . This can be caused by a defective oven temperature sensor or the electronic range control (ERC). You can’t test the ERC, but you can test the oven sensor.

What does e2 f1 mean on a Whirlpool oven?

F1 – E2 – UL A/D Error(s) – Disconnect power for at least 30 seconds and then reconnect. Allow at least a minute after power has been restored and if error code reappears, replace control board (clock).

How do I fix my oven f2?

If the F2 error code has frozen on the oven after shutting down, then unplug the oven for 30 seconds. Plug the oven back in and see if the error code appears again.