Maytag f1 code

What does it mean when my oven says f1?

The F1 error means that there is an electronics failure within the oven . This failure can occur within the keypad itself, the electronic oven control or the oven temperature sensor.

How do I reset my Maytag stove?

Simply turn off the oven , unplug it for five minutes, and then plug it back in and restart . Also, make sure the fuse wasn’t tripped at the circuit breaker and that the outlet provides the correct voltage for the oven .

How do you clear the error code on a Maytag washer?

To remove the code , press pause or cancel button twice and the power button once. If the code is still displayed, unplug the washer or disconnect the power for one minute. Items were detected in the washer during the Clean Washer cycle. Remove items from the drum and restart the Clean Washer cycle.

How do I fix f9 error on Maytag oven?

How to Remove the F9 Code From Maytag Hold on the “Start/Stop” button for 10 seconds. This will end the beeping. Open the oven door and check the door latch. If it wiggles, it needs to be tightened. Spray a little WD-40 onto a washcloth and scrub off any rust or debris on the latch. Press the oven door shut gently. Test the oven .

How do I fix f1 error on Whirlpool oven?

F1 Error Code There may be an analog to digital failure; if this is the case, simply disconnect the range for 30 seconds and plug back in. If the same display reappears, you may need to replace the control board.

You might be interested:  F1 gp schedule

What does e2 f1 mean on a Whirlpool oven?

F1 – E2 – UL A/D Error(s) – Disconnect power for at least 30 seconds and then reconnect. Allow at least a minute after power has been restored and if error code reappears, replace control board (clock).

How do I reset my Maytag Gemini stove?

Reset power to the product: Power unit down by turning off the circuit breaker(s) for one (1) minute. Power unit up by turning on the circuit breaker(s). Monitor the oven / range for one (1) minute to ensure the error code does not display again. Verify oven operation.

Do stoves have a reset button?

Some older ovens have their own set of fuses located under the range top, in the back of the oven space, or behind the oven. Your oven might also have a circuit breaker with a reset button on the control console or on top of the oven that needs to be reset . If you are still confounded, pull the oven away from the wall.

How do you fix an f1 oven?

When an F1 error occurs, the display flashes the code and beeps at the same time. To stop the flashing and beeping, press the “Cancel” button. Try the bake or broil feature once more, and if the error code repeats, unplug the appliance and wait five minutes before plugging it back in.

What does F mean on Maytag washer?

Common solutions for: Maytag F /02 – Drain Cycle Too Long The manufacturer has assigned this error or fault code to indicate that the washing machine drain cycle is taking too long. After 8 minutes of drain time the error code is displayed. Press PAUSE/CANCEL twice to clear the display.

You might be interested:  F1 visa summer internship

What does f5 mean on my washing machine?

Error code F05 on some Hotpoint (and some Indesit) washing machines means the pressure switch has “jammed” on. So the washing machine thinks it is full of water and refuses to spin. If this is the case then clearly when the fault occurs the drum should be full of water or at least still have a fair amount inside.

How do I fix error code f9?

The F9 error usually means the door switch circuit system is faulty. This can be addressed by checking the door switch itself. If the door switch is dirty or caught in one position, use a damp cloth to wipe the switch clean and then wiggle the switch slightly to make sure the switch moves back and forth.

How do I clear f9 code?

The error code ” F9 ” indicates a failure with the latch motor. Since the door did not physically lock, open the door and locate the door light switch plunger. Push and hold the door light plunger in and then press Clear /Off while continuing to press in on the door plunger.

What does f9 error code mean?

An F9 error code on a General Electric (GE) oven indicates that the oven’s electronic control system has detected a problem with the automatic door lock. The malfunction may be a jammed door lock mechanism, a pinched or broken wire, a faulty lock switch or a fault in the control board itself.