Kenmore elite oasis washer f1 error code

What does f1 mean on Kenmore Elite washer?

The F1 error code indicates a problem with the water level pressure transducer signal on the machine control board.

How do I reset my Kenmore Elite Oasis washer?

How to Reset a Sears Kenmore Elite Oasis Washer Press “Stop” to clear the current cycle on the washer . Press the “Power” button to turn off the washer . Unplug the washer from the power supply. Wait several minutes. Plug the Oasis washer back into the power supply and press the “Power” button to turn on the washer . Select the desired wash cycle and press “Start.”

How do I fix the code on my Kenmore washer?

Kenmore front-load washer LE error code Overloaded washer . Make sure the washer isn’t overloaded. Too much detergent. If you see lots of suds in the tub, let the washer sit idle for 30 minutes so the foam dissipates. Drive system obstruction. Loose wiring or defective drive motor.

How do I fix the Sud error on my Kenmore Elite washer?

Suds are the foam caused by agitation of the detergent. If a non-HE detergent is used, or too much detergent is used, this problem can occur. The machine will automatically try to reduce the suds by adding a rinse cycle but if it can’t reduce the suds enough it may pause the cycle.

What does it mean when a washer says f1?

error code

How do I run diagnostics on my Kenmore Elite washer?

Here is what I did to run a diagnostic . With the washer empty, close the door. Push “control/on” or “Start” Select “Drain/Spin” Select “No Spin” by pressing SPIN SPEED touchpad. Push “PREWASH” option four times within 5 seconds. C:00 should light up and begin the diagnostic .

You might be interested:  F1 car horsepower

Is there a reset button on Kenmore Elite washer?

If you have started a load in your Kenmore Elite HE washer and need to reset it, simply press several buttons on the control panel.

How do I reset my Kenmore Elite top load washer?

Press the “Stop” button twice, and then press the “Power” button. Choose a wash cycle (e.g. “Normal”), and then choose your wash options (e.g. “Hot/Cold” or “Cold/Cold”). Press the “Start” button to complete the reset process and restart the washing machine .

How do I reset my Kenmore front load washer?

How to Reset a Kenmore 3.5 Capacity Washer Turn off and unplug the machine. Unlock the control panel by simultaneously pushing and holding down the Options and Select button for 10 seconds if you see a lock icon on the control display. Push whichever new options you need, and wait for the control panel to flash and reset the washer’s options.

How do you reset the sensor on a Kenmore washing machine?

Top Load Washer – Hydrowave Motor Reset Unplug the washer for 1 minute from the electrical outlet. Plug the washer back in and lift and lower the lid 6 times within a 12 second period. You have 30 seconds to start lifting and lowering the lid. The motor has now been reset and is ready for you to start a cycle.

Is there a reset button on a washing machine?

Most newer washing machines come with a reset feature that allows you to restart the washer after it experiences an error code or fault. Some machines have a button you push to reset its motor. On a machine without a reset button , unplugging the washer and then plugging it back in often serves as the means to reset it.

You might be interested:  F1 news michael schumacher

How do you drain a Kenmore front load washer?

How do you drain a Kenmore front load washer ? Open the drain pump filter door, pull out the drain tube and remove the drain tube plug. Allow any water left in the washer to drain into the pan. Pull the filter out of the pump and clear any debris from the filter and pump housing.

How do I fix the Sud error on my washing machine?

To solve this SUDS issue, finish your current load, if possible. Then run the washer on the largest load possible with no detergent and using hot water. This should rinse away the excess. However, if it still feels slimy inside, you may need to repeat as necessary.

How do I fix SD error code?

Simply put, too much detergent was used and an excessive amount of suds or foam was produced. Adding an additional rinse cycle without adding any more detergent might fix this problem. Sometimes the machine will automatically detects this problem and add a pause and additional rinse cycle in order to break up the suds.

What do you do when your washer says suds?

It means you are using detergent improperly. If your washing machine has the word ” SUDS ” on the display, it has detected an over-sudsing condition, and will stop for a short period to allow the suds to dissipate. This error code is usually caused by too much detergent, or the wrong type of detergent.