Fisher paykel f1 error

How do I reset my Fisher and Paykel DishDrawer?

How do I reset my Fisher Paykel Dishdrawer ? Press and hold the button decorated with the key and lock image for five seconds. Press the power button to turn off power to the Fisher & Paykel dishwasher. Wait a few minutes and then press the power button to restore power. Turn off and unplug the dishwasher if the issue remains.

What does f1 mean on dishwasher?

F1 means that there is water in the base pan below the bottom drawer. This usually happens because something was stacked too high in one of the drawers when it was running and this caused the lid to not seal up when the drawer was shut.

What does f5 mean on Fisher and Paykel dishwasher?

Fisher and Paykel Dishwasher Dishdrawer Error Code F5 Error Code Cause: Lid Error. How To Fix: Turn power to DishDrawer off then turn on power supply. This may reset error. If not the Lid lock switch needs to be checked.

How do I fix Fisher and Paykel dishwasher f1 error?

F1 Fault Code Water in the drain pan can also be caused by a drain blockage, a clogged filter, a faulty lid seal or a leaking water-inlet valve. Turn off the water supply immediately to the machine. Shut off power to the unit by unplugging it from the wall or flip the circuit breaker switch to the Off position.

Why is my Fisher and Paykel dishwasher not draining?

Straighten any kinks along the hose that drains water from your DishDrawer ™. If the kinks return, you may need to replace the hose. Clean the filter plate/ drain filter. Aim to clean your DishDrawer ™ at least once per month, including the drain filter plates.

You might be interested:  Difference between f1 and f2 goldendoodles

What does f4 mean on a dishwasher?

water pump failure

What does f9 mean on a dishwasher?

divisor position error

Why is my DishDrawer not draining?

Disconnect the drain hose at both connection points. You may need a small adjustable wrench to do this. Stagnant water may be trapped in the hose, so remove it carefully and pour any trapped water down the sink. If you can see obstructions, the drain hose is likely the cause of your drainage problems.

How do you run a diagnostic on a Fisher Paykel dishwasher?

Diagnostic Mode. With Power off, press/hold Keylock, then press Start/Pause at the same time for 5 seconds. Release the buttons when it powers-on. Press Power once.

What is fault 49 on Fisher and Paykel Aquasmart?

@stevew Error Fault Condition – Water Inlet Valve Fault . Repair or Check – Unplug the washer from power. If the resistance of each water inlet valve solenoid is not 60 to 62 ohms then replace the complete water inlet valve assembly.

Why is my DishDrawer beeping?

The DishDrawer ® will beep six times to indicate the end of the wash programme. It is normal for some water to remain in the drain filter area after the wash programme is complete. Double models only: At the end of a wash programme, you may find both drawers draining simultaneously.

How do you manually drain Fisher Paykel DishDrawer?

How do you drain a Fisher Paykel DishDrawer ? Obtain a copy of the instruction manual for your specific model of Fisher & Paykel dishwasher. Use the diagrams in the manual to locate the food trap. Use the diagrams in the manual to locate your dishwasher’s drain hose. Disconnect the drain hose at both connection points. Look up the pump assembly in the manual .

You might be interested:  F1 visa interview questions and answers

How do I reset my DishDrawer?

Reset Procedures for the Fisher & Paykel Dishwasher Press and hold the button decorated with the key and lock image for five seconds. Press the power button to turn off power to the Fisher & Paykel dishwasher. Wait a few minutes and then press the power button to restore power. Turn off and unplug the dishwasher if the issue remains.