Fisher paykel dishwasher f1

What does f1 mean on my Fisher and Paykel dishwasher?

The F1 fault code indicates that water has filled the flood pan beneath the bottom drawer of the machine. Water in the drain pan can also be caused by a drain blockage, a clogged filter, a faulty lid seal or a leaking water-inlet valve.

How do I reset my Fisher and Paykel dishwasher?

Reset Procedures for the Fisher & Paykel Dishwasher Press and hold the button decorated with the key and lock image for five seconds. Press the power button to turn off power to the Fisher & Paykel dishwasher . Wait a few minutes and then press the power button to restore power.

How do I get my Fisher and Paykel dishwasher to stop beeping?

disconnecting the dishwasher from the water and power supplies, and contact Customer Care. Press ► to stop the beeping . Press ► again to turn the dishwasher off. Wait a few seconds.

How do I fix the f2 on my Fisher and Paykel dishwasher?

Reset Procedures for the Fisher & Paykel Dishwasher Press the power button to turn off power to the Fisher & Paykel dishwasher . Wait a few minutes and then press the power button to restore power. Turn off and unplug the dishwasher if the issue remains.

What does f9 mean on a dishwasher?

divisor position error

Why is my DishDrawer not draining?

Disconnect the drain hose at both connection points. You may need a small adjustable wrench to do this. Stagnant water may be trapped in the hose, so remove it carefully and pour any trapped water down the sink. If you can see obstructions, the drain hose is likely the cause of your drainage problems.

You might be interested:  Ge oven f1 error code

Why is my Fisher and Paykel dishwasher not draining?

Straighten any kinks along the hose that drains water from your DishDrawer ™. If the kinks return, you may need to replace the hose. Clean the filter plate/ drain filter. Aim to clean your DishDrawer ™ at least once per month, including the drain filter plates.

How do you run a diagnostic on a Fisher Paykel dishwasher?

Diagnostic Mode. With Power off, press/hold Keylock, then press Start/Pause at the same time for 5 seconds. Release the buttons when it powers-on. Press Power once.

How do I fix e4 error on Fisher and Paykel dishwasher?

How To Fix : Be sure the drain hose is connected per the installation instructions. Fisher and Paykel Dishwasher Dishdrawer Error Code E4 = Program indicator lights 1, 3, and 4 are flashing. Error Code Cause: Drain hose is too high. Drain hose is kinked.

Why is my DishDrawer beeping?

The DishDrawer ® will beep six times to indicate the end of the wash programme. It is normal for some water to remain in the drain filter area after the wash programme is complete. Double models only: At the end of a wash programme, you may find both drawers draining simultaneously.

Do Fisher and Paykel dishwashers heat their own water?

Yes it does – all dishwashers heat their own water . Wash water is not as hot as rinse water , by having its own heater it can regulate the temperature.

How do I reset my DishDrawer?

How do I reset my DishDrawer ? Press and hold the button decorated with the key and lock image for five seconds. Press the power button to turn off power to the Fisher & Paykel dishwasher. Wait a few minutes and then press the power button to restore power. Turn off and unplug the dishwasher if the issue remains.

You might be interested:  Sky sports f1 commentator

Where is the flood switch on a Fisher and Paykel dishwasher?

The anti flood switch is in the bottom of the bas of the dishwasher . If its activated try and pull the dishwasher out and tip it 45 degs backwards and the water should drain out from the base and that way the flood switch will reset itself.

What is f2 in dishwasher?

The F2 code means that water level exceeds the admissible one. This may be due to a blocked or faulty drain pump and/or inlet valve. This is a common problem, because food particles often get stuck in the drain system and prevent dishwashers from draining properly.

What does f4 mean on a Fisher and Paykel dishwasher?

Error F4 appear, the dishwasher beeps continuously and there is water in the bottom. We can only turn off at the wall. What does F4 mean and how can we fix it? Greetings The F4 code means that the machine has sensed that the water temperature is not rising while the heating element is energized.