F1 code on whirlpool dryer

How do I fix f1 error on Whirlpool Cabrio dryer?

When the Whirlpool Cabrio displays an F1 error , this means the the control board is having difficulty communicating with the motor. To fix your F1 error , you can first try to unplug your washing machine for 15 minutes and then plug it back in. If this doesn’t work, you will need to replace the control board.

How do I reset my Whirlpool front load dryer?

If your Whirlpool dryer displays a “PF” error code, indicating a recent power failure, the dryer will need to be reset and restarted. This is done by pressing “Start” for a few seconds to restart the dryer . If the dryer does not restart automatically, select a new cycle and any options then press “Start” to begin.

How do I find the code on my Whirlpool Duet dryer?

press and hold for three seconds, release for three seconds; press and hold for three seconds. You’ll know you’ve entered diagnostic mode because all the indicators on the console will light up for five seconds and you’ll see the code “88” in the Estimated Time Remaining display.

What does it mean when your dryer says f1?

The ” F1 ” error means that the dryer’s thermistor failed. The dryer is reading the thermistor as “open” and the actual part has shorted out. The thermistor is used to read and control temperatures within the dryer . Without the part, the dryer will not operate.

What is f1 error on Whirlpool Cabrio?

The Cabrio Washer F1 error code happens when the main control board gets a bad signal from the water level pressure switch circuit. This is normally caused by a pinched or ripped water level pressure switch hose.

You might be interested:  Australian f1 grand prix

Why is my Whirlpool dryer not coming on?

The thermal fuse is the most common problem with Whirlpool dryers not running. The thermal fuse cuts the dryer off in the event it overheats. So if your thermal fuse is bad you should check the vent. To check the thermal fuse, first unplug dryer and remove back.

Where is the reset button on a dryer?

There is no reset button on your dryer . I recommend locating the two (2) house circuit breakers dedicated for the dryer and reset both circuit breakers by flipping them both OFF and ON 2-3 times and then check to see if the dryer will start.

What do you do when your dryer won’t start?

Unplug the dryer and check the thermal fuse for continuity. Replace the thermal fuse if the multimeter measures no continuity. Check the exhaust vent because a clog in the vent likely caused the thermal fuse to blow. For dryers with a dial timer, a broken push-to- start switch can prevent the motor from running.

How do you test a dryer control board?

How to test your dryer’s rotary switch: Unplug your dryer and remove the control console panel on the top of your dryer to locate the rotary switch. Set your multi-meter to the Rx1 setting and place the probes on the switch’s terminals. With the probes still touching the terminals, press in on and hold the switch.

What does error code f01 mean?

failed electronic machine control board

What does the code f70 mean on a Whirlpool Duet dryer?

I talked to Whirlpool this morning and they said that the F 70 error code indicates some kind of communication problem between the component electronics and the control electronics.

You might be interested:  F1 2014 game

How do I reset my Whirlpool Duet dryer?

How do I reset my Whirlpool Duet steam dryer ? Inspect household fuses or breakers. Close the dryer door firmly. Press and hold the “Start” button for five seconds. Check the display on the dryer for error codes. Press the “Start” button and hold for several seconds to restart the dryer if “PF” appears on the display.

How do you troubleshoot a Whirlpool Cabrio dryer?

Troubleshooting your Whirlpool Cabrio will take about 15 minutes. Verify that the dryer is still plugged into its outlet. Ensure that your household fuses or breakers are active. Push the dryer door to make sure it is tightly closed. Press and hold the “Start/Pause” button for up to five seconds.