F1 code on whirlpool cabrio washer

What does it mean when a washer says f1?

error code

How do you clear the error code on a Whirlpool Cabrio washer?

Try the Cabrio Reset Procedure Touch any button that you see on your display pad. This will clear the error code . Or you can press PAUSE/CANCEL. Choose a cycle and press START.

Does a Whirlpool Cabrio Washer have a filter?

Whirlpool Cabrio top-loading washing machines are equipped with a drain pump and filter to prevent clogging the washing machine …

How do I fix f1 error on Whirlpool Cabrio dryer?

When the Whirlpool Cabrio displays an F1 error , this means the the control board is having difficulty communicating with the motor. To fix your F1 error , you can first try to unplug your washing machine for 15 minutes and then plug it back in. If this doesn’t work, you will need to replace the control board.

What does Code F mean on a Cabrio washer?

door lock error

How do I know if my washing machine control board is bad?

A failed front-load washing machine control board has several symptoms, including the washer not starting, filling, spinning or draining.

How do I reset my Whirlpool Cabrio Top load washer?

Press the Start Stop button once. Rotate the dial until Rinse, Wash, and Stop light illuminate. Turn the washer off and unplug it for 10 seconds. Finally, turn on the washer and it should now be reset .

How do you troubleshoot a Whirlpool Cabrio washer?

Troubleshooting Whirlpool Cabrio Washer Problems Washer Making Unusual Noises. Washer Won’t Start. Lid Lock Issues . Deciphering the LD Error Code. Washer Leaves Deposits on Dark Clothes. Washer Has a Burned Plastic Odor. Rust Spots on Washer Lid.

You might be interested:  Can i apply for f1 visa while in us

Why won’t my Cabrio washer fill with water?

If you find your Whirlpool Cabrio washer not filling with water , the inlet hoses and screens may be at fault. Metal screens attached to both ends of the inlet hoses protect the water inlet valve from sediment and debris. To inspect the screens for signs of clogging, turn off the main water supply.

Where is filter on Whirlpool Cabrio washing machine?

Find your washing machine filter . For front-loading machines , the filter will be in the bottom right corner on the outside of the washer . If you have an older top-loading washer , your filter will also be in the bottom right-hand corner of the machine .

Where is the filter on a top load Whirlpool washer?

Top Load Washer – Lint / Pump Filters There are 2 crescent-shaped Fine Mesh plastic lint filters in the bottom of the wash basket, under the agitator. During drain down and spin, the water forces the lint off the bottom of the filters and down the drain. These filters should never require cleaning or replacement.

How do I clean sludge out of my top loader washing machine?

Steps To Cleaning a Top – Loader With Vinegar: Turn your washing machine on the hot water setting (largest load possible) and let it fill up. Once it begins to agitate, open the lid to make it stop. Now, add about 3 cups of filtered white apple cider vinegar. Add ¾ cup of baking soda and stir it the mixture.

How do I fix f01 error?

The F01 indicates a failed electronic machine control board. This error code can sometimes be caused by a glitch or power surge through the electrical lines. You may be able to clear this code by unplugging the washer for 5 minutes.

You might be interested:  F1 team names

Where is the error code on a Whirlpool Cabrio dryer?

Whirlpool Cabrio Dryer Error Codes AF – Exhaust air flow restriction. PF – Power failure. F-01 – Main control failure. F-02 – User interface (UI) keypad failure. F-22 or F-23 – Exhaust thermistor failure. F-26 – Drive motor failure. F-28 or F-29 – Moisture sensor failure. F-31 – Low L2 voltage.